Том 8 № 4

Постійне посилання зібрання

Переглянути

Нові надходження

Зараз показуємо 1 - 5 з 11
  • Документ
    IMPROVEMENT OF MANAGEMENT OF STEAM GENERATORS IN NUCLEAR AND THERMAL POWER PLANTS
    (2017) I. Slobodyan, V. Lozhechny`kov, A. Stopakevy`ch
    The paper formulated optimization problem formulation production of carbon products. The analysis of technical and economic parameters that can be used to optimize the production of carbonaceous products had been done by the author. To evaluate the efficiency of the energy-intensive production uses several technical and economic indicators. In particular, the specific cost, productivity, income and profitability of production. Based on a detailed analysis had been formulated optimality criterion that takes into account the technological components of profitability. The components in detail the criteria and the proposed method of calculating non-trivial, one of them - the production cost of each product. When solving the optimization problem of technological modes of production into account constraints on the variables are optimized. Thus, restrictions may be expressed on the number of each product produced. Have been formulated the method of calculating the cost per unit of product. Attention is paid to the quality indices of finished products as an additional constraint in the optimization problem. As a result have been formulated the general problem of optimizing the production of carbon products, which includes the optimality criterion and restrictions.
  • Документ
    ЛИНЕАРИЗАЦИЯ В ЗАДАЧЕ УПРАВЛЕНИЯ ХАРАКТЕРИСТИКОЙ ЦИФРОВОГО ФИЛЬТРА ДЛЯ СПЕЦИАЛИЗИРОВАННОЙ КОМПЬЮТЕРНОЙ СИСТЕМЫ
    (2017) А. В. Ухина, Т. П. Яценко, В. С. Ситников
    dependencies that could be used to obtain linear characteristic of frequency response control are defined. The possibility of such control is shown.
  • Документ
    CONCEPT OF AUTOMATIC CONTROL SYSTEM FOR IMPROVING THE EFFICIENCY OF THE ABSORPTION REFRIGERATING UNITS
    (2017) O. Titlova, V. Khobin, O. Titlov
    The general concept of the automatic control systems constructing for increasing the efficiency of the artificial cold production process in the absorption refrigerating units is substantiated. The described automatic control systems provides necessary degree of the ammonia vapor purification from the water in all absorption refrigerating units modes and minimizes heat loss from the dephlegmator surface.
  • Документ
    MODEL-ORIENTED METHOD OF DESIGN IMPLEMENTATION WHEN CREATING DIGITAL FILTERS
    (2017) V. Levinskyi, M. Levinskyi
    This article discusses the example of model-oriented method of design and development of digital low-pass filters (LPF) for automatic control systems (ACS). Typically, high frequency noise and disturbance attenuation is carried out by analogue LPF. However, technical implementation of analogue filters higher than the second order arouse certain difficulties related with the need of precise passive components ratings selection (resistors, capacitors). If the noise and disturbances spectral composition is known, it is possible to build digital LPF with the Nyquist frequency greater than the maximum frequency in the noise spectrum. Such possibility has appeared because of cheap, energy-efficient, high-speed 32-bit microcontrollers market entry. They have analogue signals sampling rate of 30 kHz and above. The traditional approach using the “manual” method of filter parameters calculation, obtaining their recurrence expressions and further program implementation requires high qualification and a lot of time consumption from the developer. An alternative to this approach is the model-oriented method of design (MOMD) in MatLab environment when in the one environment the design of digital LPF, verificaton of its performance as a part of the ACS, generation and compilation of program codes for selected microcontroller family take place. MOMD can also be used in the designs of bandpass and bandstop filters for adaptive control systems or systems of technical diagnostics. If during the commissioning or the operation of ACS there is a need in digital LPF parameters change then this operation can be performed within half an hour. MOMD technology allows to significantly reduce the time for developing a specific product without loss of quality in its design ‘cause of extensive possibilities of MatLab development environment.
  • Документ
    INVESTIGATION AND ANALYSIS OF AUTOMATIC TESTING SYSTEMS OF APPLICATIONS
    (2017) A. Antonova, A. Proydenko, A. Bodnia
    The focus of this article has been about automated testing in practice. Using testing tools is quite common phenomenon in software companies. The article studied the use of software testing tools. Testing software is enough ordinary things in the IT software development company. But the using automated testing tools only develop in the educational training of IT professionals. Information study of the use of testing tools for the control of software quality IT professionals and IT students was held. Statistical analysis of the data shows the percentage of how many people use the testing tools, but most still depends on manual testing. The main purpose of the article is to find out the facts related to the research questions of creation of new testing tools for educational purposes of highly qualified IT professionals.